![differential cylinder_zbd1611_ Storz Hydraulik Differentialzylinder](https://storzhydraulik.de/wp-content/uploads/2018/12/differentialzylinder_zbd1611_.jpg)
Storz Hydraulik Differentialzylinder Storz Hydraulik Differentialzylinder
Technical Documents
ZBD 1611 – Standard hydraulic cylinders (ISO 6020/1) – Nominal pressure 160 bar (16 MPa)
Good to know: The STORZ ZBD 1611 series hydraulic cylinder for a nominal pressure of 160 bar complies with ISO 6020/1 and VW 39D920 standards.
- International interchangeability thanks to the definition of the mounting dimensions, installation length, surface ratios, piston rod ends and connecting threads
- Same installation dimensions for cylinders with and without end position damping
- Two rod diameters assigned to each piston diameter as standard (corresponding area ratios j=1.4 and j=2)
- Position for line connections, vents and throttle screws is freely configurable
- 8 standardized mounting types and 6 sealing variants as standard
Technical data
Nominal pressure: | 160 bar (16 MPa) |
Static test pressure: | 240 bar (24 MPa) |
Piston diameter: | 25-200 mm |
Area ratio j: | 1,4 and 2 |
Temperature range: | -20…+80 °C |
Viscosity range: | 10…600 mm²/s |
Lifting speed: | 0 – 1 m/s depending on seal variant |
Operating medium: | Mineral oil according to DIN 51524, HFD fluids HFA, HFB and HFC fluids possible through special design |
Mounting types
![1611_a 1611_a](https://storzhydraulik.de/wp-content/uploads/2018/12/1611_a.png)
A Basic design
![1611_mt4 1611_mt4](https://storzhydraulik.de/wp-content/uploads/2018/12/1611_mt4.png)
MT4 Trunnion
![1611_mf3 1611_mf3](https://storzhydraulik.de/wp-content/uploads/2018/12/1611_mf3.png)
MF3 round flange on cylinder head
![1611_mf4 1611_mf4](https://storzhydraulik.de/wp-content/uploads/2018/12/1611_mf4.png)
MF4 round flange at cylinder bottom
![1611_mf1 1611_mf1](https://storzhydraulik.de/wp-content/uploads/2018/12/1611_mf1.png)
MF1 rectangular flange on cylinder head
![1611_mf2 1611_mf2](https://storzhydraulik.de/wp-content/uploads/2018/12/1611_mf2.png)
MF2 rectangular flange at cylinder bottom
![1611_mp4 1611_mp4](https://storzhydraulik.de/wp-content/uploads/2018/12/1611_mp4.png)
MP4 Swivel eye at cylinder bottom
![1611_mp6 1611_mp6](https://storzhydraulik.de/wp-content/uploads/2018/12/1611_mp6.png)
MP6 Joint eye at cylinder bottom
![1611_ms2 1611_ms2](https://storzhydraulik.de/wp-content/uploads/2018/12/1611_ms2.png)
MS2 Foot mounting
![1001_a-](https://storzhydraulik.de/wp-content/uploads/2018/11/1001_a-.png)
![1001_b-](https://storzhydraulik.de/wp-content/uploads/2018/11/1001_b-.png)
![1001_ca-](https://storzhydraulik.de/wp-content/uploads/2018/11/1001_ca-.png)
![1001_b-](https://storzhydraulik.de/wp-content/uploads/2018/11/1001_b-.png)